manda-node03, manda-node04: lvm: issue discards
[mirror/dsa-puppet.git] / modules / dsa_lvm / files / lvm-ganeti.manda.debian.org.conf
1 # This is an example configuration file for the LVM2 system.
2 # It contains the default settings that would be used if there was no
3 # /etc/lvm/lvm.conf file.
4 #
5 # Refer to 'man lvm.conf' for further information including the file layout.
6 #
7 # Refer to 'man lvm.conf' for information about how settings configured in
8 # this file are combined with built-in values and command line options to
9 # arrive at the final values used by LVM.
10 #
11 # Refer to 'man lvmconfig' for information about displaying the built-in
12 # and configured values used by LVM.
13 #
14 # If a default value is set in this file (not commented out), then a
15 # new version of LVM using this file will continue using that value,
16 # even if the new version of LVM changes the built-in default value.
17 #
18 # To put this file in a different directory and override /etc/lvm set
19 # the environment variable LVM_SYSTEM_DIR before running the tools.
20 #
21 # N.B. Take care that each setting only appears once if uncommenting
22 # example settings in this file.
23
24
25 # Configuration section config.
26 # How LVM configuration settings are handled.
27 config {
28
29         # Configuration option config/checks.
30         # If enabled, any LVM configuration mismatch is reported.
31         # This implies checking that the configuration key is understood by
32         # LVM and that the value of the key is the proper type. If disabled,
33         # any configuration mismatch is ignored and the default value is used
34         # without any warning (a message about the configuration key not being
35         # found is issued in verbose mode only).
36         checks = 1
37
38         # Configuration option config/abort_on_errors.
39         # Abort the LVM process if a configuration mismatch is found.
40         abort_on_errors = 0
41
42         # Configuration option config/profile_dir.
43         # Directory where LVM looks for configuration profiles.
44         profile_dir = "/etc/lvm/profile"
45 }
46
47 # Configuration section devices.
48 # How LVM uses block devices.
49 devices {
50
51         # Configuration option devices/dir.
52         # Directory in which to create volume group device nodes.
53         # Commands also accept this as a prefix on volume group names.
54         # This configuration option is advanced.
55         dir = "/dev"
56
57         # Configuration option devices/scan.
58         # Directories containing device nodes to use with LVM.
59         # This configuration option is advanced.
60         scan = [ "/dev" ]
61
62         # Configuration option devices/obtain_device_list_from_udev.
63         # Obtain the list of available devices from udev.
64         # This avoids opening or using any inapplicable non-block devices or
65         # subdirectories found in the udev directory. Any device node or
66         # symlink not managed by udev in the udev directory is ignored. This
67         # setting applies only to the udev-managed device directory; other
68         # directories will be scanned fully. LVM needs to be compiled with
69         # udev support for this setting to apply.
70         obtain_device_list_from_udev = 1
71
72         # Configuration option devices/external_device_info_source.
73         # Select an external device information source.
74         # Some information may already be available in the system and LVM can
75         # use this information to determine the exact type or use of devices it
76         # processes. Using an existing external device information source can
77         # speed up device processing as LVM does not need to run its own native
78         # routines to acquire this information. For example, this information
79         # is used to drive LVM filtering like MD component detection, multipath
80         # component detection, partition detection and others.
81         # 
82         # Accepted values:
83         #   none
84         #     No external device information source is used.
85         #   udev
86         #     Reuse existing udev database records. Applicable only if LVM is
87         #     compiled with udev support.
88         # 
89         external_device_info_source = "none"
90
91         # Configuration option devices/preferred_names.
92         # Select which path name to display for a block device.
93         # If multiple path names exist for a block device, and LVM needs to
94         # display a name for the device, the path names are matched against
95         # each item in this list of regular expressions. The first match is
96         # used. Try to avoid using undescriptive /dev/dm-N names, if present.
97         # If no preferred name matches, or if preferred_names are not defined,
98         # the following built-in preferences are applied in order until one
99         # produces a preferred name:
100         # Prefer names with path prefixes in the order of:
101         # /dev/mapper, /dev/disk, /dev/dm-*, /dev/block.
102         # Prefer the name with the least number of slashes.
103         # Prefer a name that is a symlink.
104         # Prefer the path with least value in lexicographical order.
105         # 
106         # Example
107         # preferred_names = [ "^/dev/mpath/", "^/dev/mapper/mpath", "^/dev/[hs]d" ]
108         # 
109         # This configuration option does not have a default value defined.
110
111         # Configuration option devices/filter.
112         # Limit the block devices that are used by LVM commands.
113         # This is a list of regular expressions used to accept or reject block
114         # device path names. Each regex is delimited by a vertical bar '|'
115         # (or any character) and is preceded by 'a' to accept the path, or
116         # by 'r' to reject the path. The first regex in the list to match the
117         # path is used, producing the 'a' or 'r' result for the device.
118         # When multiple path names exist for a block device, if any path name
119         # matches an 'a' pattern before an 'r' pattern, then the device is
120         # accepted. If all the path names match an 'r' pattern first, then the
121         # device is rejected. Unmatching path names do not affect the accept
122         # or reject decision. If no path names for a device match a pattern,
123         # then the device is accepted. Be careful mixing 'a' and 'r' patterns,
124         # as the combination might produce unexpected results (test changes.)
125         # Run vgscan after changing the filter to regenerate the cache.
126         # See the use_lvmetad comment for a special case regarding filters.
127         # 
128         # Example
129         # Accept every block device:
130         # filter = [ "a|.*/|" ]
131         # Reject the cdrom drive:
132         # filter = [ "r|/dev/cdrom|" ]
133         # Work with just loopback devices, e.g. for testing:
134         # filter = [ "a|loop|", "r|.*|" ]
135         # Accept all loop devices and ide drives except hdc:
136         # filter = [ "a|loop|", "r|/dev/hdc|", "a|/dev/ide|", "r|.*|" ]
137         # Use anchors to be very specific:
138         # filter = [ "a|^/dev/hda8$|", "r|.*/|" ]
139         # 
140         # This configuration option has an automatic default value.
141         # filter = [ "a|.*/|" ]
142         filter = [ "a|^/dev/sd[ab][0-9]*$|", "r/.*/" ]
143
144         # Configuration option devices/global_filter.
145         # Limit the block devices that are used by LVM system components.
146         # Because devices/filter may be overridden from the command line, it is
147         # not suitable for system-wide device filtering, e.g. udev and lvmetad.
148         # Use global_filter to hide devices from these LVM system components.
149         # The syntax is the same as devices/filter. Devices rejected by
150         # global_filter are not opened by LVM.
151         # This configuration option has an automatic default value.
152         # global_filter = [ "a|.*/|" ]
153
154         # Configuration option devices/cache_dir.
155         # Directory in which to store the device cache file.
156         # The results of filtering are cached on disk to avoid rescanning dud
157         # devices (which can take a very long time). By default this cache is
158         # stored in a file named .cache. It is safe to delete this file; the
159         # tools regenerate it. If obtain_device_list_from_udev is enabled, the
160         # list of devices is obtained from udev and any existing .cache file
161         # is removed.
162         cache_dir = "/run/lvm"
163
164         # Configuration option devices/cache_file_prefix.
165         # A prefix used before the .cache file name. See devices/cache_dir.
166         cache_file_prefix = ""
167
168         # Configuration option devices/write_cache_state.
169         # Enable/disable writing the cache file. See devices/cache_dir.
170         write_cache_state = 1
171
172         # Configuration option devices/types.
173         # List of additional acceptable block device types.
174         # These are of device type names from /proc/devices, followed by the
175         # maximum number of partitions.
176         # 
177         # Example
178         # types = [ "fd", 16 ]
179         # 
180         # This configuration option is advanced.
181         # This configuration option does not have a default value defined.
182
183         # Configuration option devices/sysfs_scan.
184         # Restrict device scanning to block devices appearing in sysfs.
185         # This is a quick way of filtering out block devices that are not
186         # present on the system. sysfs must be part of the kernel and mounted.)
187         sysfs_scan = 1
188
189         # Configuration option devices/multipath_component_detection.
190         # Ignore devices that are components of DM multipath devices.
191         multipath_component_detection = 1
192
193         # Configuration option devices/md_component_detection.
194         # Ignore devices that are components of software RAID (md) devices.
195         md_component_detection = 1
196
197         # Configuration option devices/fw_raid_component_detection.
198         # Ignore devices that are components of firmware RAID devices.
199         # LVM must use an external_device_info_source other than none for this
200         # detection to execute.
201         fw_raid_component_detection = 0
202
203         # Configuration option devices/md_chunk_alignment.
204         # Align PV data blocks with md device's stripe-width.
205         # This applies if a PV is placed directly on an md device.
206         md_chunk_alignment = 1
207
208         # Configuration option devices/default_data_alignment.
209         # Default alignment of the start of a PV data area in MB.
210         # If set to 0, a value of 64KiB will be used.
211         # Set to 1 for 1MiB, 2 for 2MiB, etc.
212         # This configuration option has an automatic default value.
213         # default_data_alignment = 1
214
215         # Configuration option devices/data_alignment_detection.
216         # Detect PV data alignment based on sysfs device information.
217         # The start of a PV data area will be a multiple of minimum_io_size or
218         # optimal_io_size exposed in sysfs. minimum_io_size is the smallest
219         # request the device can perform without incurring a read-modify-write
220         # penalty, e.g. MD chunk size. optimal_io_size is the device's
221         # preferred unit of receiving I/O, e.g. MD stripe width.
222         # minimum_io_size is used if optimal_io_size is undefined (0).
223         # If md_chunk_alignment is enabled, that detects the optimal_io_size.
224         # This setting takes precedence over md_chunk_alignment.
225         data_alignment_detection = 1
226
227         # Configuration option devices/data_alignment.
228         # Alignment of the start of a PV data area in KiB.
229         # If a PV is placed directly on an md device and md_chunk_alignment or
230         # data_alignment_detection are enabled, then this setting is ignored.
231         # Otherwise, md_chunk_alignment and data_alignment_detection are
232         # disabled if this is set. Set to 0 to use the default alignment or the
233         # page size, if larger.
234         data_alignment = 0
235
236         # Configuration option devices/data_alignment_offset_detection.
237         # Detect PV data alignment offset based on sysfs device information.
238         # The start of a PV aligned data area will be shifted by the
239         # alignment_offset exposed in sysfs. This offset is often 0, but may
240         # be non-zero. Certain 4KiB sector drives that compensate for windows
241         # partitioning will have an alignment_offset of 3584 bytes (sector 7
242         # is the lowest aligned logical block, the 4KiB sectors start at
243         # LBA -1, and consequently sector 63 is aligned on a 4KiB boundary).
244         # pvcreate --dataalignmentoffset will skip this detection.
245         data_alignment_offset_detection = 1
246
247         # Configuration option devices/ignore_suspended_devices.
248         # Ignore DM devices that have I/O suspended while scanning devices.
249         # Otherwise, LVM waits for a suspended device to become accessible.
250         # This should only be needed in recovery situations.
251         ignore_suspended_devices = 0
252
253         # Configuration option devices/ignore_lvm_mirrors.
254         # Do not scan 'mirror' LVs to avoid possible deadlocks.
255         # This avoids possible deadlocks when using the 'mirror' segment type.
256         # This setting determines whether LVs using the 'mirror' segment type
257         # are scanned for LVM labels. This affects the ability of mirrors to
258         # be used as physical volumes. If this setting is enabled, it is
259         # impossible to create VGs on top of mirror LVs, i.e. to stack VGs on
260         # mirror LVs. If this setting is disabled, allowing mirror LVs to be
261         # scanned, it may cause LVM processes and I/O to the mirror to become
262         # blocked. This is due to the way that the mirror segment type handles
263         # failures. In order for the hang to occur, an LVM command must be run
264         # just after a failure and before the automatic LVM repair process
265         # takes place, or there must be failures in multiple mirrors in the
266         # same VG at the same time with write failures occurring moments before
267         # a scan of the mirror's labels. The 'mirror' scanning problems do not
268         # apply to LVM RAID types like 'raid1' which handle failures in a
269         # different way, making them a better choice for VG stacking.
270         ignore_lvm_mirrors = 1
271
272         # Configuration option devices/disable_after_error_count.
273         # Number of I/O errors after which a device is skipped.
274         # During each LVM operation, errors received from each device are
275         # counted. If the counter of a device exceeds the limit set here,
276         # no further I/O is sent to that device for the remainder of the
277         # operation. Setting this to 0 disables the counters altogether.
278         disable_after_error_count = 0
279
280         # Configuration option devices/require_restorefile_with_uuid.
281         # Allow use of pvcreate --uuid without requiring --restorefile.
282         require_restorefile_with_uuid = 1
283
284         # Configuration option devices/pv_min_size.
285         # Minimum size in KiB of block devices which can be used as PVs.
286         # In a clustered environment all nodes must use the same value.
287         # Any value smaller than 512KiB is ignored. The previous built-in
288         # value was 512.
289         pv_min_size = 2048
290
291         # Configuration option devices/issue_discards.
292         # Issue discards to PVs that are no longer used by an LV.
293         # Discards are sent to an LV's underlying physical volumes when the LV
294         # is no longer using the physical volumes' space, e.g. lvremove,
295         # lvreduce. Discards inform the storage that a region is no longer
296         # used. Storage that supports discards advertise the protocol-specific
297         # way discards should be issued by the kernel (TRIM, UNMAP, or
298         # WRITE SAME with UNMAP bit set). Not all storage will support or
299         # benefit from discards, but SSDs and thinly provisioned LUNs
300         # generally do. If enabled, discards will only be issued if both the
301         # storage and kernel provide support.
302         issue_discards = 1
303
304         # Configuration option devices/allow_changes_with_duplicate_pvs.
305         # Allow VG modification while a PV appears on multiple devices.
306         # When a PV appears on multiple devices, LVM attempts to choose the
307         # best device to use for the PV. If the devices represent the same
308         # underlying storage, the choice has minimal consequence. If the
309         # devices represent different underlying storage, the wrong choice
310         # can result in data loss if the VG is modified. Disabling this
311         # setting is the safest option because it prevents modifying a VG
312         # or activating LVs in it while a PV appears on multiple devices.
313         # Enabling this setting allows the VG to be used as usual even with
314         # uncertain devices.
315         allow_changes_with_duplicate_pvs = 0
316 }
317
318 # Configuration section allocation.
319 # How LVM selects space and applies properties to LVs.
320 allocation {
321
322         # Configuration option allocation/cling_tag_list.
323         # Advise LVM which PVs to use when searching for new space.
324         # When searching for free space to extend an LV, the 'cling' allocation
325         # policy will choose space on the same PVs as the last segment of the
326         # existing LV. If there is insufficient space and a list of tags is
327         # defined here, it will check whether any of them are attached to the
328         # PVs concerned and then seek to match those PV tags between existing
329         # extents and new extents.
330         # 
331         # Example
332         # Use the special tag "@*" as a wildcard to match any PV tag:
333         # cling_tag_list = [ "@*" ]
334         # LVs are mirrored between two sites within a single VG, and
335         # PVs are tagged with either @site1 or @site2 to indicate where
336         # they are situated:
337         # cling_tag_list = [ "@site1", "@site2" ]
338         # 
339         # This configuration option does not have a default value defined.
340
341         # Configuration option allocation/maximise_cling.
342         # Use a previous allocation algorithm.
343         # Changes made in version 2.02.85 extended the reach of the 'cling'
344         # policies to detect more situations where data can be grouped onto
345         # the same disks. This setting can be used to disable the changes
346         # and revert to the previous algorithm.
347         maximise_cling = 1
348
349         # Configuration option allocation/use_blkid_wiping.
350         # Use blkid to detect existing signatures on new PVs and LVs.
351         # The blkid library can detect more signatures than the native LVM
352         # detection code, but may take longer. LVM needs to be compiled with
353         # blkid wiping support for this setting to apply. LVM native detection
354         # code is currently able to recognize: MD device signatures,
355         # swap signature, and LUKS signatures. To see the list of signatures
356         # recognized by blkid, check the output of the 'blkid -k' command.
357         use_blkid_wiping = 1
358
359         # Configuration option allocation/wipe_signatures_when_zeroing_new_lvs.
360         # Look for and erase any signatures while zeroing a new LV.
361         # The --wipesignatures option overrides this setting.
362         # Zeroing is controlled by the -Z/--zero option, and if not specified,
363         # zeroing is used by default if possible. Zeroing simply overwrites the
364         # first 4KiB of a new LV with zeroes and does no signature detection or
365         # wiping. Signature wiping goes beyond zeroing and detects exact types
366         # and positions of signatures within the whole LV. It provides a
367         # cleaner LV after creation as all known signatures are wiped. The LV
368         # is not claimed incorrectly by other tools because of old signatures
369         # from previous use. The number of signatures that LVM can detect
370         # depends on the detection code that is selected (see
371         # use_blkid_wiping.) Wiping each detected signature must be confirmed.
372         # When this setting is disabled, signatures on new LVs are not detected
373         # or erased unless the --wipesignatures option is used directly.
374         wipe_signatures_when_zeroing_new_lvs = 1
375
376         # Configuration option allocation/mirror_logs_require_separate_pvs.
377         # Mirror logs and images will always use different PVs.
378         # The default setting changed in version 2.02.85.
379         mirror_logs_require_separate_pvs = 0
380
381         # Configuration option allocation/raid_stripe_all_devices.
382         # Stripe across all PVs when RAID stripes are not specified.
383         # If enabled, all PVs in the VG or on the command line are used for raid0/4/5/6/10
384         # when the command does not specify the number of stripes to use.
385         # This was the default behaviour until release 2.02.162.
386         # This configuration option has an automatic default value.
387         # raid_stripe_all_devices = 0
388
389         # Configuration option allocation/cache_pool_metadata_require_separate_pvs.
390         # Cache pool metadata and data will always use different PVs.
391         cache_pool_metadata_require_separate_pvs = 0
392
393         # Configuration option allocation/cache_mode.
394         # The default cache mode used for new cache.
395         # 
396         # Accepted values:
397         #   writethrough
398         #     Data blocks are immediately written from the cache to disk.
399         #   writeback
400         #     Data blocks are written from the cache back to disk after some
401         #     delay to improve performance.
402         # 
403         # This setting replaces allocation/cache_pool_cachemode.
404         # This configuration option has an automatic default value.
405         # cache_mode = "writethrough"
406
407         # Configuration option allocation/cache_policy.
408         # The default cache policy used for new cache volume.
409         # Since kernel 4.2 the default policy is smq (Stochastic multique),
410         # otherwise the older mq (Multiqueue) policy is selected.
411         # This configuration option does not have a default value defined.
412
413         # Configuration section allocation/cache_settings.
414         # Settings for the cache policy.
415         # See documentation for individual cache policies for more info.
416         # This configuration section has an automatic default value.
417         # cache_settings {
418         # }
419
420         # Configuration option allocation/cache_pool_chunk_size.
421         # The minimal chunk size in KiB for cache pool volumes.
422         # Using a chunk_size that is too large can result in wasteful use of
423         # the cache, where small reads and writes can cause large sections of
424         # an LV to be mapped into the cache. However, choosing a chunk_size
425         # that is too small can result in more overhead trying to manage the
426         # numerous chunks that become mapped into the cache. The former is
427         # more of a problem than the latter in most cases, so the default is
428         # on the smaller end of the spectrum. Supported values range from
429         # 32KiB to 1GiB in multiples of 32.
430         # This configuration option does not have a default value defined.
431
432         # Configuration option allocation/cache_pool_max_chunks.
433         # The maximum number of chunks in a cache pool.
434         # For cache target v1.9 the recommended maximumm is 1000000 chunks.
435         # Using cache pool with more chunks may degrade cache performance.
436         # This configuration option does not have a default value defined.
437
438         # Configuration option allocation/thin_pool_metadata_require_separate_pvs.
439         # Thin pool metdata and data will always use different PVs.
440         thin_pool_metadata_require_separate_pvs = 0
441
442         # Configuration option allocation/thin_pool_zero.
443         # Thin pool data chunks are zeroed before they are first used.
444         # Zeroing with a larger thin pool chunk size reduces performance.
445         # This configuration option has an automatic default value.
446         # thin_pool_zero = 1
447
448         # Configuration option allocation/thin_pool_discards.
449         # The discards behaviour of thin pool volumes.
450         # 
451         # Accepted values:
452         #   ignore
453         #   nopassdown
454         #   passdown
455         # 
456         # This configuration option has an automatic default value.
457         # thin_pool_discards = "passdown"
458
459         # Configuration option allocation/thin_pool_chunk_size_policy.
460         # The chunk size calculation policy for thin pool volumes.
461         # 
462         # Accepted values:
463         #   generic
464         #     If thin_pool_chunk_size is defined, use it. Otherwise, calculate
465         #     the chunk size based on estimation and device hints exposed in
466         #     sysfs - the minimum_io_size. The chunk size is always at least
467         #     64KiB.
468         #   performance
469         #     If thin_pool_chunk_size is defined, use it. Otherwise, calculate
470         #     the chunk size for performance based on device hints exposed in
471         #     sysfs - the optimal_io_size. The chunk size is always at least
472         #     512KiB.
473         # 
474         # This configuration option has an automatic default value.
475         # thin_pool_chunk_size_policy = "generic"
476
477         # Configuration option allocation/thin_pool_chunk_size.
478         # The minimal chunk size in KiB for thin pool volumes.
479         # Larger chunk sizes may improve performance for plain thin volumes,
480         # however using them for snapshot volumes is less efficient, as it
481         # consumes more space and takes extra time for copying. When unset,
482         # lvm tries to estimate chunk size starting from 64KiB. Supported
483         # values are in the range 64KiB to 1GiB.
484         # This configuration option does not have a default value defined.
485
486         # Configuration option allocation/physical_extent_size.
487         # Default physical extent size in KiB to use for new VGs.
488         # This configuration option has an automatic default value.
489         # physical_extent_size = 4096
490 }
491
492 # Configuration section log.
493 # How LVM log information is reported.
494 log {
495
496         # Configuration option log/report_command_log.
497         # Enable or disable LVM log reporting.
498         # If enabled, LVM will collect a log of operations, messages,
499         # per-object return codes with object identification and associated
500         # error numbers (errnos) during LVM command processing. Then the
501         # log is either reported solely or in addition to any existing
502         # reports, depending on LVM command used. If it is a reporting command
503         # (e.g. pvs, vgs, lvs, lvm fullreport), then the log is reported in
504         # addition to any existing reports. Otherwise, there's only log report
505         # on output. For all applicable LVM commands, you can request that
506         # the output has only log report by using --logonly command line
507         # option. Use log/command_log_cols and log/command_log_sort settings
508         # to define fields to display and sort fields for the log report.
509         # You can also use log/command_log_selection to define selection
510         # criteria used each time the log is reported.
511         # This configuration option has an automatic default value.
512         # report_command_log = 0
513
514         # Configuration option log/command_log_sort.
515         # List of columns to sort by when reporting command log.
516         # See <lvm command> --logonly --configreport log -o help
517         # for the list of possible fields.
518         # This configuration option has an automatic default value.
519         # command_log_sort = "log_seq_num"
520
521         # Configuration option log/command_log_cols.
522         # List of columns to report when reporting command log.
523         # See <lvm command> --logonly --configreport log -o help
524         # for the list of possible fields.
525         # This configuration option has an automatic default value.
526         # command_log_cols = "log_seq_num,log_type,log_context,log_object_type,log_object_name,log_object_id,log_object_group,log_object_group_id,log_message,log_errno,log_ret_code"
527
528         # Configuration option log/command_log_selection.
529         # Selection criteria used when reporting command log.
530         # You can define selection criteria that are applied each
531         # time log is reported. This way, it is possible to control the
532         # amount of log that is displayed on output and you can select
533         # only parts of the log that are important for you. To define
534         # selection criteria, use fields from log report. See also
535         # <lvm command> --logonly --configreport log -S help for the
536         # list of possible fields and selection operators. You can also
537         # define selection criteria for log report on command line directly
538         # using <lvm command> --configreport log -S <selection criteria>
539         # which has precedence over log/command_log_selection setting.
540         # For more information about selection criteria in general, see
541         # lvm(8) man page.
542         # This configuration option has an automatic default value.
543         # command_log_selection = "!(log_type=status && message=success)"
544
545         # Configuration option log/verbose.
546         # Controls the messages sent to stdout or stderr.
547         verbose = 0
548
549         # Configuration option log/silent.
550         # Suppress all non-essential messages from stdout.
551         # This has the same effect as -qq. When enabled, the following commands
552         # still produce output: dumpconfig, lvdisplay, lvmdiskscan, lvs, pvck,
553         # pvdisplay, pvs, version, vgcfgrestore -l, vgdisplay, vgs.
554         # Non-essential messages are shifted from log level 4 to log level 5
555         # for syslog and lvm2_log_fn purposes.
556         # Any 'yes' or 'no' questions not overridden by other arguments are
557         # suppressed and default to 'no'.
558         silent = 0
559
560         # Configuration option log/syslog.
561         # Send log messages through syslog.
562         syslog = 1
563
564         # Configuration option log/file.
565         # Write error and debug log messages to a file specified here.
566         # This configuration option does not have a default value defined.
567
568         # Configuration option log/overwrite.
569         # Overwrite the log file each time the program is run.
570         overwrite = 0
571
572         # Configuration option log/level.
573         # The level of log messages that are sent to the log file or syslog.
574         # There are 6 syslog-like log levels currently in use: 2 to 7 inclusive.
575         # 7 is the most verbose (LOG_DEBUG).
576         level = 0
577
578         # Configuration option log/indent.
579         # Indent messages according to their severity.
580         indent = 1
581
582         # Configuration option log/command_names.
583         # Display the command name on each line of output.
584         command_names = 0
585
586         # Configuration option log/prefix.
587         # A prefix to use before the log message text.
588         # (After the command name, if selected).
589         # Two spaces allows you to see/grep the severity of each message.
590         # To make the messages look similar to the original LVM tools use:
591         # indent = 0, command_names = 1, prefix = " -- "
592         prefix = "  "
593
594         # Configuration option log/activation.
595         # Log messages during activation.
596         # Don't use this in low memory situations (can deadlock).
597         activation = 0
598
599         # Configuration option log/debug_classes.
600         # Select log messages by class.
601         # Some debugging messages are assigned to a class and only appear in
602         # debug output if the class is listed here. Classes currently
603         # available: memory, devices, activation, allocation, lvmetad,
604         # metadata, cache, locking, lvmpolld. Use "all" to see everything.
605         debug_classes = [ "memory", "devices", "activation", "allocation", "lvmetad", "metadata", "cache", "locking", "lvmpolld", "dbus" ]
606 }
607
608 # Configuration section backup.
609 # How LVM metadata is backed up and archived.
610 # In LVM, a 'backup' is a copy of the metadata for the current system,
611 # and an 'archive' contains old metadata configurations. They are
612 # stored in a human readable text format.
613 backup {
614
615         # Configuration option backup/backup.
616         # Maintain a backup of the current metadata configuration.
617         # Think very hard before turning this off!
618         backup = 1
619
620         # Configuration option backup/backup_dir.
621         # Location of the metadata backup files.
622         # Remember to back up this directory regularly!
623         backup_dir = "/etc/lvm/backup"
624
625         # Configuration option backup/archive.
626         # Maintain an archive of old metadata configurations.
627         # Think very hard before turning this off.
628         archive = 1
629
630         # Configuration option backup/archive_dir.
631         # Location of the metdata archive files.
632         # Remember to back up this directory regularly!
633         archive_dir = "/etc/lvm/archive"
634
635         # Configuration option backup/retain_min.
636         # Minimum number of archives to keep.
637         retain_min = 10
638
639         # Configuration option backup/retain_days.
640         # Minimum number of days to keep archive files.
641         retain_days = 30
642 }
643
644 # Configuration section shell.
645 # Settings for running LVM in shell (readline) mode.
646 shell {
647
648         # Configuration option shell/history_size.
649         # Number of lines of history to store in ~/.lvm_history.
650         history_size = 100
651 }
652
653 # Configuration section global.
654 # Miscellaneous global LVM settings.
655 global {
656
657         # Configuration option global/umask.
658         # The file creation mask for any files and directories created.
659         # Interpreted as octal if the first digit is zero.
660         umask = 077
661
662         # Configuration option global/test.
663         # No on-disk metadata changes will be made in test mode.
664         # Equivalent to having the -t option on every command.
665         test = 0
666
667         # Configuration option global/units.
668         # Default value for --units argument.
669         units = "h"
670
671         # Configuration option global/si_unit_consistency.
672         # Distinguish between powers of 1024 and 1000 bytes.
673         # The LVM commands distinguish between powers of 1024 bytes,
674         # e.g. KiB, MiB, GiB, and powers of 1000 bytes, e.g. KB, MB, GB.
675         # If scripts depend on the old behaviour, disable this setting
676         # temporarily until they are updated.
677         si_unit_consistency = 1
678
679         # Configuration option global/suffix.
680         # Display unit suffix for sizes.
681         # This setting has no effect if the units are in human-readable form
682         # (global/units = "h") in which case the suffix is always displayed.
683         suffix = 1
684
685         # Configuration option global/activation.
686         # Enable/disable communication with the kernel device-mapper.
687         # Disable to use the tools to manipulate LVM metadata without
688         # activating any logical volumes. If the device-mapper driver
689         # is not present in the kernel, disabling this should suppress
690         # the error messages.
691         activation = 1
692
693         # Configuration option global/fallback_to_lvm1.
694         # Try running LVM1 tools if LVM cannot communicate with DM.
695         # This option only applies to 2.4 kernels and is provided to help
696         # switch between device-mapper kernels and LVM1 kernels. The LVM1
697         # tools need to be installed with .lvm1 suffices, e.g. vgscan.lvm1.
698         # They will stop working once the lvm2 on-disk metadata format is used.
699         # This configuration option has an automatic default value.
700         # fallback_to_lvm1 = 0
701
702         # Configuration option global/format.
703         # The default metadata format that commands should use.
704         # The -M 1|2 option overrides this setting.
705         # 
706         # Accepted values:
707         #   lvm1
708         #   lvm2
709         # 
710         # This configuration option has an automatic default value.
711         # format = "lvm2"
712
713         # Configuration option global/format_libraries.
714         # Shared libraries that process different metadata formats.
715         # If support for LVM1 metadata was compiled as a shared library use
716         # format_libraries = "liblvm2format1.so"
717         # This configuration option does not have a default value defined.
718
719         # Configuration option global/segment_libraries.
720         # This configuration option does not have a default value defined.
721
722         # Configuration option global/proc.
723         # Location of proc filesystem.
724         # This configuration option is advanced.
725         proc = "/proc"
726
727         # Configuration option global/etc.
728         # Location of /etc system configuration directory.
729         etc = "/etc"
730
731         # Configuration option global/locking_type.
732         # Type of locking to use.
733         # 
734         # Accepted values:
735         #   0
736         #     Turns off locking. Warning: this risks metadata corruption if
737         #     commands run concurrently.
738         #   1
739         #     LVM uses local file-based locking, the standard mode.
740         #   2
741         #     LVM uses the external shared library locking_library.
742         #   3
743         #     LVM uses built-in clustered locking with clvmd.
744         #     This is incompatible with lvmetad. If use_lvmetad is enabled,
745         #     LVM prints a warning and disables lvmetad use.
746         #   4
747         #     LVM uses read-only locking which forbids any operations that
748         #     might change metadata.
749         #   5
750         #     Offers dummy locking for tools that do not need any locks.
751         #     You should not need to set this directly; the tools will select
752         #     when to use it instead of the configured locking_type.
753         #     Do not use lvmetad or the kernel device-mapper driver with this
754         #     locking type. It is used by the --readonly option that offers
755         #     read-only access to Volume Group metadata that cannot be locked
756         #     safely because it belongs to an inaccessible domain and might be
757         #     in use, for example a virtual machine image or a disk that is
758         #     shared by a clustered machine.
759         # 
760         locking_type = 1
761
762         # Configuration option global/wait_for_locks.
763         # When disabled, fail if a lock request would block.
764         wait_for_locks = 1
765
766         # Configuration option global/fallback_to_clustered_locking.
767         # Attempt to use built-in cluster locking if locking_type 2 fails.
768         # If using external locking (type 2) and initialisation fails, with
769         # this enabled, an attempt will be made to use the built-in clustered
770         # locking. Disable this if using a customised locking_library.
771         fallback_to_clustered_locking = 1
772
773         # Configuration option global/fallback_to_local_locking.
774         # Use locking_type 1 (local) if locking_type 2 or 3 fail.
775         # If an attempt to initialise type 2 or type 3 locking failed, perhaps
776         # because cluster components such as clvmd are not running, with this
777         # enabled, an attempt will be made to use local file-based locking
778         # (type 1). If this succeeds, only commands against local VGs will
779         # proceed. VGs marked as clustered will be ignored.
780         fallback_to_local_locking = 1
781
782         # Configuration option global/locking_dir.
783         # Directory to use for LVM command file locks.
784         # Local non-LV directory that holds file-based locks while commands are
785         # in progress. A directory like /tmp that may get wiped on reboot is OK.
786         locking_dir = "/run/lock/lvm"
787
788         # Configuration option global/prioritise_write_locks.
789         # Allow quicker VG write access during high volume read access.
790         # When there are competing read-only and read-write access requests for
791         # a volume group's metadata, instead of always granting the read-only
792         # requests immediately, delay them to allow the read-write requests to
793         # be serviced. Without this setting, write access may be stalled by a
794         # high volume of read-only requests. This option only affects
795         # locking_type 1 viz. local file-based locking.
796         prioritise_write_locks = 1
797
798         # Configuration option global/library_dir.
799         # Search this directory first for shared libraries.
800         # This configuration option does not have a default value defined.
801
802         # Configuration option global/locking_library.
803         # The external locking library to use for locking_type 2.
804         # This configuration option has an automatic default value.
805         # locking_library = "liblvm2clusterlock.so"
806
807         # Configuration option global/abort_on_internal_errors.
808         # Abort a command that encounters an internal error.
809         # Treat any internal errors as fatal errors, aborting the process that
810         # encountered the internal error. Please only enable for debugging.
811         abort_on_internal_errors = 0
812
813         # Configuration option global/detect_internal_vg_cache_corruption.
814         # Internal verification of VG structures.
815         # Check if CRC matches when a parsed VG is used multiple times. This
816         # is useful to catch unexpected changes to cached VG structures.
817         # Please only enable for debugging.
818         detect_internal_vg_cache_corruption = 0
819
820         # Configuration option global/metadata_read_only.
821         # No operations that change on-disk metadata are permitted.
822         # Additionally, read-only commands that encounter metadata in need of
823         # repair will still be allowed to proceed exactly as if the repair had
824         # been performed (except for the unchanged vg_seqno). Inappropriate
825         # use could mess up your system, so seek advice first!
826         metadata_read_only = 0
827
828         # Configuration option global/mirror_segtype_default.
829         # The segment type used by the short mirroring option -m.
830         # The --type mirror|raid1 option overrides this setting.
831         # 
832         # Accepted values:
833         #   mirror
834         #     The original RAID1 implementation from LVM/DM. It is
835         #     characterized by a flexible log solution (core, disk, mirrored),
836         #     and by the necessity to block I/O while handling a failure.
837         #     There is an inherent race in the dmeventd failure handling logic
838         #     with snapshots of devices using this type of RAID1 that in the
839         #     worst case could cause a deadlock. (Also see
840         #     devices/ignore_lvm_mirrors.)
841         #   raid1
842         #     This is a newer RAID1 implementation using the MD RAID1
843         #     personality through device-mapper. It is characterized by a
844         #     lack of log options. (A log is always allocated for every
845         #     device and they are placed on the same device as the image,
846         #     so no separate devices are required.) This mirror
847         #     implementation does not require I/O to be blocked while
848         #     handling a failure. This mirror implementation is not
849         #     cluster-aware and cannot be used in a shared (active/active)
850         #     fashion in a cluster.
851         # 
852         mirror_segtype_default = "raid1"
853
854         # Configuration option global/raid10_segtype_default.
855         # The segment type used by the -i -m combination.
856         # The --type raid10|mirror option overrides this setting.
857         # The --stripes/-i and --mirrors/-m options can both be specified
858         # during the creation of a logical volume to use both striping and
859         # mirroring for the LV. There are two different implementations.
860         # 
861         # Accepted values:
862         #   raid10
863         #     LVM uses MD's RAID10 personality through DM. This is the
864         #     preferred option.
865         #   mirror
866         #     LVM layers the 'mirror' and 'stripe' segment types. The layering
867         #     is done by creating a mirror LV on top of striped sub-LVs,
868         #     effectively creating a RAID 0+1 array. The layering is suboptimal
869         #     in terms of providing redundancy and performance.
870         # 
871         raid10_segtype_default = "raid10"
872
873         # Configuration option global/sparse_segtype_default.
874         # The segment type used by the -V -L combination.
875         # The --type snapshot|thin option overrides this setting.
876         # The combination of -V and -L options creates a sparse LV. There are
877         # two different implementations.
878         # 
879         # Accepted values:
880         #   snapshot
881         #     The original snapshot implementation from LVM/DM. It uses an old
882         #     snapshot that mixes data and metadata within a single COW
883         #     storage volume and performs poorly when the size of stored data
884         #     passes hundreds of MB.
885         #   thin
886         #     A newer implementation that uses thin provisioning. It has a
887         #     bigger minimal chunk size (64KiB) and uses a separate volume for
888         #     metadata. It has better performance, especially when more data
889         #     is used. It also supports full snapshots.
890         # 
891         sparse_segtype_default = "thin"
892
893         # Configuration option global/lvdisplay_shows_full_device_path.
894         # Enable this to reinstate the previous lvdisplay name format.
895         # The default format for displaying LV names in lvdisplay was changed
896         # in version 2.02.89 to show the LV name and path separately.
897         # Previously this was always shown as /dev/vgname/lvname even when that
898         # was never a valid path in the /dev filesystem.
899         # This configuration option has an automatic default value.
900         # lvdisplay_shows_full_device_path = 0
901
902         # Configuration option global/use_lvmetad.
903         # Use lvmetad to cache metadata and reduce disk scanning.
904         # When enabled (and running), lvmetad provides LVM commands with VG
905         # metadata and PV state. LVM commands then avoid reading this
906         # information from disks which can be slow. When disabled (or not
907         # running), LVM commands fall back to scanning disks to obtain VG
908         # metadata. lvmetad is kept updated via udev rules which must be set
909         # up for LVM to work correctly. (The udev rules should be installed
910         # by default.) Without a proper udev setup, changes in the system's
911         # block device configuration will be unknown to LVM, and ignored
912         # until a manual 'pvscan --cache' is run. If lvmetad was running
913         # while use_lvmetad was disabled, it must be stopped, use_lvmetad
914         # enabled, and then started. When using lvmetad, LV activation is
915         # switched to an automatic, event-based mode. In this mode, LVs are
916         # activated based on incoming udev events that inform lvmetad when
917         # PVs appear on the system. When a VG is complete (all PVs present),
918         # it is auto-activated. The auto_activation_volume_list setting
919         # controls which LVs are auto-activated (all by default.)
920         # When lvmetad is updated (automatically by udev events, or directly
921         # by pvscan --cache), devices/filter is ignored and all devices are
922         # scanned by default. lvmetad always keeps unfiltered information
923         # which is provided to LVM commands. Each LVM command then filters
924         # based on devices/filter. This does not apply to other, non-regexp,
925         # filtering settings: component filters such as multipath and MD
926         # are checked during pvscan --cache. To filter a device and prevent
927         # scanning from the LVM system entirely, including lvmetad, use
928         # devices/global_filter.
929         use_lvmetad = 1
930
931         # Configuration option global/lvmetad_update_wait_time.
932         # The number of seconds a command will wait for lvmetad update to finish.
933         # After waiting for this period, a command will not use lvmetad, and
934         # will revert to disk scanning.
935         # This configuration option has an automatic default value.
936         # lvmetad_update_wait_time = 10
937
938         # Configuration option global/use_lvmlockd.
939         # Use lvmlockd for locking among hosts using LVM on shared storage.
940         # Applicable only if LVM is compiled with lockd support in which
941         # case there is also lvmlockd(8) man page available for more
942         # information.
943         use_lvmlockd = 0
944
945         # Configuration option global/lvmlockd_lock_retries.
946         # Retry lvmlockd lock requests this many times.
947         # Applicable only if LVM is compiled with lockd support
948         # This configuration option has an automatic default value.
949         # lvmlockd_lock_retries = 3
950
951         # Configuration option global/sanlock_lv_extend.
952         # Size in MiB to extend the internal LV holding sanlock locks.
953         # The internal LV holds locks for each LV in the VG, and after enough
954         # LVs have been created, the internal LV needs to be extended. lvcreate
955         # will automatically extend the internal LV when needed by the amount
956         # specified here. Setting this to 0 disables the automatic extension
957         # and can cause lvcreate to fail. Applicable only if LVM is compiled
958         # with lockd support
959         # This configuration option has an automatic default value.
960         # sanlock_lv_extend = 256
961
962         # Configuration option global/thin_check_executable.
963         # The full path to the thin_check command.
964         # LVM uses this command to check that a thin metadata device is in a
965         # usable state. When a thin pool is activated and after it is
966         # deactivated, this command is run. Activation will only proceed if
967         # the command has an exit status of 0. Set to "" to skip this check.
968         # (Not recommended.) Also see thin_check_options.
969         # (See package device-mapper-persistent-data or thin-provisioning-tools)
970         # This configuration option has an automatic default value.
971         # thin_check_executable = "/usr/sbin/thin_check"
972
973         # Configuration option global/thin_dump_executable.
974         # The full path to the thin_dump command.
975         # LVM uses this command to dump thin pool metadata.
976         # (See package device-mapper-persistent-data or thin-provisioning-tools)
977         # This configuration option has an automatic default value.
978         # thin_dump_executable = "/usr/sbin/thin_dump"
979
980         # Configuration option global/thin_repair_executable.
981         # The full path to the thin_repair command.
982         # LVM uses this command to repair a thin metadata device if it is in
983         # an unusable state. Also see thin_repair_options.
984         # (See package device-mapper-persistent-data or thin-provisioning-tools)
985         # This configuration option has an automatic default value.
986         # thin_repair_executable = "/usr/sbin/thin_repair"
987
988         # Configuration option global/thin_check_options.
989         # List of options passed to the thin_check command.
990         # With thin_check version 2.1 or newer you can add the option
991         # --ignore-non-fatal-errors to let it pass through ignorable errors
992         # and fix them later. With thin_check version 3.2 or newer you should
993         # include the option --clear-needs-check-flag.
994         # This configuration option has an automatic default value.
995         # thin_check_options = [ "-q", "--clear-needs-check-flag" ]
996
997         # Configuration option global/thin_repair_options.
998         # List of options passed to the thin_repair command.
999         # This configuration option has an automatic default value.
1000         # thin_repair_options = [ "" ]
1001
1002         # Configuration option global/thin_disabled_features.
1003         # Features to not use in the thin driver.
1004         # This can be helpful for testing, or to avoid using a feature that is
1005         # causing problems. Features include: block_size, discards,
1006         # discards_non_power_2, external_origin, metadata_resize,
1007         # external_origin_extend, error_if_no_space.
1008         # 
1009         # Example
1010         # thin_disabled_features = [ "discards", "block_size" ]
1011         # 
1012         # This configuration option does not have a default value defined.
1013
1014         # Configuration option global/cache_disabled_features.
1015         # Features to not use in the cache driver.
1016         # This can be helpful for testing, or to avoid using a feature that is
1017         # causing problems. Features include: policy_mq, policy_smq.
1018         # 
1019         # Example
1020         # cache_disabled_features = [ "policy_smq" ]
1021         # 
1022         # This configuration option does not have a default value defined.
1023
1024         # Configuration option global/cache_check_executable.
1025         # The full path to the cache_check command.
1026         # LVM uses this command to check that a cache metadata device is in a
1027         # usable state. When a cached LV is activated and after it is
1028         # deactivated, this command is run. Activation will only proceed if the
1029         # command has an exit status of 0. Set to "" to skip this check.
1030         # (Not recommended.) Also see cache_check_options.
1031         # (See package device-mapper-persistent-data or thin-provisioning-tools)
1032         # This configuration option has an automatic default value.
1033         # cache_check_executable = "/usr/sbin/cache_check"
1034
1035         # Configuration option global/cache_dump_executable.
1036         # The full path to the cache_dump command.
1037         # LVM uses this command to dump cache pool metadata.
1038         # (See package device-mapper-persistent-data or thin-provisioning-tools)
1039         # This configuration option has an automatic default value.
1040         # cache_dump_executable = "/usr/sbin/cache_dump"
1041
1042         # Configuration option global/cache_repair_executable.
1043         # The full path to the cache_repair command.
1044         # LVM uses this command to repair a cache metadata device if it is in
1045         # an unusable state. Also see cache_repair_options.
1046         # (See package device-mapper-persistent-data or thin-provisioning-tools)
1047         # This configuration option has an automatic default value.
1048         # cache_repair_executable = "/usr/sbin/cache_repair"
1049
1050         # Configuration option global/cache_check_options.
1051         # List of options passed to the cache_check command.
1052         # With cache_check version 5.0 or newer you should include the option
1053         # --clear-needs-check-flag.
1054         # This configuration option has an automatic default value.
1055         # cache_check_options = [ "-q", "--clear-needs-check-flag" ]
1056
1057         # Configuration option global/cache_repair_options.
1058         # List of options passed to the cache_repair command.
1059         # This configuration option has an automatic default value.
1060         # cache_repair_options = [ "" ]
1061
1062         # Configuration option global/system_id_source.
1063         # The method LVM uses to set the local system ID.
1064         # Volume Groups can also be given a system ID (by vgcreate, vgchange,
1065         # or vgimport.) A VG on shared storage devices is accessible only to
1066         # the host with a matching system ID. See 'man lvmsystemid' for
1067         # information on limitations and correct usage.
1068         # 
1069         # Accepted values:
1070         #   none
1071         #     The host has no system ID.
1072         #   lvmlocal
1073         #     Obtain the system ID from the system_id setting in the 'local'
1074         #     section of an lvm configuration file, e.g. lvmlocal.conf.
1075         #   uname
1076         #     Set the system ID from the hostname (uname) of the system.
1077         #     System IDs beginning localhost are not permitted.
1078         #   machineid
1079         #     Use the contents of the machine-id file to set the system ID.
1080         #     Some systems create this file at installation time.
1081         #     See 'man machine-id' and global/etc.
1082         #   file
1083         #     Use the contents of another file (system_id_file) to set the
1084         #     system ID.
1085         # 
1086         system_id_source = "none"
1087
1088         # Configuration option global/system_id_file.
1089         # The full path to the file containing a system ID.
1090         # This is used when system_id_source is set to 'file'.
1091         # Comments starting with the character # are ignored.
1092         # This configuration option does not have a default value defined.
1093
1094         # Configuration option global/use_lvmpolld.
1095         # Use lvmpolld to supervise long running LVM commands.
1096         # When enabled, control of long running LVM commands is transferred
1097         # from the original LVM command to the lvmpolld daemon. This allows
1098         # the operation to continue independent of the original LVM command.
1099         # After lvmpolld takes over, the LVM command displays the progress
1100         # of the ongoing operation. lvmpolld itself runs LVM commands to
1101         # manage the progress of ongoing operations. lvmpolld can be used as
1102         # a native systemd service, which allows it to be started on demand,
1103         # and to use its own control group. When this option is disabled, LVM
1104         # commands will supervise long running operations by forking themselves.
1105         # Applicable only if LVM is compiled with lvmpolld support.
1106         use_lvmpolld = 1
1107
1108         # Configuration option global/notify_dbus.
1109         # Enable D-Bus notification from LVM commands.
1110         # When enabled, an LVM command that changes PVs, changes VG metadata,
1111         # or changes the activation state of an LV will send a notification.
1112         notify_dbus = 1
1113 }
1114
1115 # Configuration section activation.
1116 activation {
1117
1118         # Configuration option activation/checks.
1119         # Perform internal checks of libdevmapper operations.
1120         # Useful for debugging problems with activation. Some of the checks may
1121         # be expensive, so it's best to use this only when there seems to be a
1122         # problem.
1123         checks = 0
1124
1125         # Configuration option activation/udev_sync.
1126         # Use udev notifications to synchronize udev and LVM.
1127         # The --nodevsync option overrides this setting.
1128         # When disabled, LVM commands will not wait for notifications from
1129         # udev, but continue irrespective of any possible udev processing in
1130         # the background. Only use this if udev is not running or has rules
1131         # that ignore the devices LVM creates. If enabled when udev is not
1132         # running, and LVM processes are waiting for udev, run the command
1133         # 'dmsetup udevcomplete_all' to wake them up.
1134         udev_sync = 1
1135
1136         # Configuration option activation/udev_rules.
1137         # Use udev rules to manage LV device nodes and symlinks.
1138         # When disabled, LVM will manage the device nodes and symlinks for
1139         # active LVs itself. Manual intervention may be required if this
1140         # setting is changed while LVs are active.
1141         udev_rules = 1
1142
1143         # Configuration option activation/verify_udev_operations.
1144         # Use extra checks in LVM to verify udev operations.
1145         # This enables additional checks (and if necessary, repairs) on entries
1146         # in the device directory after udev has completed processing its
1147         # events. Useful for diagnosing problems with LVM/udev interactions.
1148         verify_udev_operations = 0
1149
1150         # Configuration option activation/retry_deactivation.
1151         # Retry failed LV deactivation.
1152         # If LV deactivation fails, LVM will retry for a few seconds before
1153         # failing. This may happen because a process run from a quick udev rule
1154         # temporarily opened the device.
1155         retry_deactivation = 1
1156
1157         # Configuration option activation/missing_stripe_filler.
1158         # Method to fill missing stripes when activating an incomplete LV.
1159         # Using 'error' will make inaccessible parts of the device return I/O
1160         # errors on access. You can instead use a device path, in which case,
1161         # that device will be used in place of missing stripes. Using anything
1162         # other than 'error' with mirrored or snapshotted volumes is likely to
1163         # result in data corruption.
1164         # This configuration option is advanced.
1165         missing_stripe_filler = "error"
1166
1167         # Configuration option activation/use_linear_target.
1168         # Use the linear target to optimize single stripe LVs.
1169         # When disabled, the striped target is used. The linear target is an
1170         # optimised version of the striped target that only handles a single
1171         # stripe.
1172         use_linear_target = 1
1173
1174         # Configuration option activation/reserved_stack.
1175         # Stack size in KiB to reserve for use while devices are suspended.
1176         # Insufficent reserve risks I/O deadlock during device suspension.
1177         reserved_stack = 64
1178
1179         # Configuration option activation/reserved_memory.
1180         # Memory size in KiB to reserve for use while devices are suspended.
1181         # Insufficent reserve risks I/O deadlock during device suspension.
1182         reserved_memory = 8192
1183
1184         # Configuration option activation/process_priority.
1185         # Nice value used while devices are suspended.
1186         # Use a high priority so that LVs are suspended
1187         # for the shortest possible time.
1188         process_priority = -18
1189
1190         # Configuration option activation/volume_list.
1191         # Only LVs selected by this list are activated.
1192         # If this list is defined, an LV is only activated if it matches an
1193         # entry in this list. If this list is undefined, it imposes no limits
1194         # on LV activation (all are allowed).
1195         # 
1196         # Accepted values:
1197         #   vgname
1198         #     The VG name is matched exactly and selects all LVs in the VG.
1199         #   vgname/lvname
1200         #     The VG name and LV name are matched exactly and selects the LV.
1201         #   @tag
1202         #     Selects an LV if the specified tag matches a tag set on the LV
1203         #     or VG.
1204         #   @*
1205         #     Selects an LV if a tag defined on the host is also set on the LV
1206         #     or VG. See tags/hosttags. If any host tags exist but volume_list
1207         #     is not defined, a default single-entry list containing '@*'
1208         #     is assumed.
1209         # 
1210         # Example
1211         # volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]
1212         # 
1213         # This configuration option does not have a default value defined.
1214
1215         # Configuration option activation/auto_activation_volume_list.
1216         # Only LVs selected by this list are auto-activated.
1217         # This list works like volume_list, but it is used only by
1218         # auto-activation commands. It does not apply to direct activation
1219         # commands. If this list is defined, an LV is only auto-activated
1220         # if it matches an entry in this list. If this list is undefined, it
1221         # imposes no limits on LV auto-activation (all are allowed.) If this
1222         # list is defined and empty, i.e. "[]", then no LVs are selected for
1223         # auto-activation. An LV that is selected by this list for
1224         # auto-activation, must also be selected by volume_list (if defined)
1225         # before it is activated. Auto-activation is an activation command that
1226         # includes the 'a' argument: --activate ay or -a ay. The 'a' (auto)
1227         # argument for auto-activation is meant to be used by activation
1228         # commands that are run automatically by the system, as opposed to LVM
1229         # commands run directly by a user. A user may also use the 'a' flag
1230         # directly to perform auto-activation. Also see pvscan(8) for more
1231         # information about auto-activation.
1232         # 
1233         # Accepted values:
1234         #   vgname
1235         #     The VG name is matched exactly and selects all LVs in the VG.
1236         #   vgname/lvname
1237         #     The VG name and LV name are matched exactly and selects the LV.
1238         #   @tag
1239         #     Selects an LV if the specified tag matches a tag set on the LV
1240         #     or VG.
1241         #   @*
1242         #     Selects an LV if a tag defined on the host is also set on the LV
1243         #     or VG. See tags/hosttags. If any host tags exist but volume_list
1244         #     is not defined, a default single-entry list containing '@*'
1245         #     is assumed.
1246         # 
1247         # Example
1248         # auto_activation_volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]
1249         # 
1250         # This configuration option does not have a default value defined.
1251
1252         # Configuration option activation/read_only_volume_list.
1253         # LVs in this list are activated in read-only mode.
1254         # If this list is defined, each LV that is to be activated is checked
1255         # against this list, and if it matches, it is activated in read-only
1256         # mode. This overrides the permission setting stored in the metadata,
1257         # e.g. from --permission rw.
1258         # 
1259         # Accepted values:
1260         #   vgname
1261         #     The VG name is matched exactly and selects all LVs in the VG.
1262         #   vgname/lvname
1263         #     The VG name and LV name are matched exactly and selects the LV.
1264         #   @tag
1265         #     Selects an LV if the specified tag matches a tag set on the LV
1266         #     or VG.
1267         #   @*
1268         #     Selects an LV if a tag defined on the host is also set on the LV
1269         #     or VG. See tags/hosttags. If any host tags exist but volume_list
1270         #     is not defined, a default single-entry list containing '@*'
1271         #     is assumed.
1272         # 
1273         # Example
1274         # read_only_volume_list = [ "vg1", "vg2/lvol1", "@tag1", "@*" ]
1275         # 
1276         # This configuration option does not have a default value defined.
1277
1278         # Configuration option activation/raid_region_size.
1279         # Size in KiB of each raid or mirror synchronization region.
1280         # For raid or mirror segment types, this is the amount of data that is
1281         # copied at once when initializing, or moved at once by pvmove.
1282         raid_region_size = 512
1283
1284         # Configuration option activation/error_when_full.
1285         # Return errors if a thin pool runs out of space.
1286         # The --errorwhenfull option overrides this setting.
1287         # When enabled, writes to thin LVs immediately return an error if the
1288         # thin pool is out of data space. When disabled, writes to thin LVs
1289         # are queued if the thin pool is out of space, and processed when the
1290         # thin pool data space is extended. New thin pools are assigned the
1291         # behavior defined here.
1292         # This configuration option has an automatic default value.
1293         # error_when_full = 0
1294
1295         # Configuration option activation/readahead.
1296         # Setting to use when there is no readahead setting in metadata.
1297         # 
1298         # Accepted values:
1299         #   none
1300         #     Disable readahead.
1301         #   auto
1302         #     Use default value chosen by kernel.
1303         # 
1304         readahead = "auto"
1305
1306         # Configuration option activation/raid_fault_policy.
1307         # Defines how a device failure in a RAID LV is handled.
1308         # This includes LVs that have the following segment types:
1309         # raid1, raid4, raid5*, and raid6*.
1310         # If a device in the LV fails, the policy determines the steps
1311         # performed by dmeventd automatically, and the steps perfomed by the
1312         # manual command lvconvert --repair --use-policies.
1313         # Automatic handling requires dmeventd to be monitoring the LV.
1314         # 
1315         # Accepted values:
1316         #   warn
1317         #     Use the system log to warn the user that a device in the RAID LV
1318         #     has failed. It is left to the user to run lvconvert --repair
1319         #     manually to remove or replace the failed device. As long as the
1320         #     number of failed devices does not exceed the redundancy of the LV
1321         #     (1 device for raid4/5, 2 for raid6), the LV will remain usable.
1322         #   allocate
1323         #     Attempt to use any extra physical volumes in the VG as spares and
1324         #     replace faulty devices.
1325         # 
1326         raid_fault_policy = "warn"
1327
1328         # Configuration option activation/mirror_image_fault_policy.
1329         # Defines how a device failure in a 'mirror' LV is handled.
1330         # An LV with the 'mirror' segment type is composed of mirror images
1331         # (copies) and a mirror log. A disk log ensures that a mirror LV does
1332         # not need to be re-synced (all copies made the same) every time a
1333         # machine reboots or crashes. If a device in the LV fails, this policy
1334         # determines the steps perfomed by dmeventd automatically, and the steps
1335         # performed by the manual command lvconvert --repair --use-policies.
1336         # Automatic handling requires dmeventd to be monitoring the LV.
1337         # 
1338         # Accepted values:
1339         #   remove
1340         #     Simply remove the faulty device and run without it. If the log
1341         #     device fails, the mirror would convert to using an in-memory log.
1342         #     This means the mirror will not remember its sync status across
1343         #     crashes/reboots and the entire mirror will be re-synced. If a
1344         #     mirror image fails, the mirror will convert to a non-mirrored
1345         #     device if there is only one remaining good copy.
1346         #   allocate
1347         #     Remove the faulty device and try to allocate space on a new
1348         #     device to be a replacement for the failed device. Using this
1349         #     policy for the log is fast and maintains the ability to remember
1350         #     sync state through crashes/reboots. Using this policy for a
1351         #     mirror device is slow, as it requires the mirror to resynchronize
1352         #     the devices, but it will preserve the mirror characteristic of
1353         #     the device. This policy acts like 'remove' if no suitable device
1354         #     and space can be allocated for the replacement.
1355         #   allocate_anywhere
1356         #     Not yet implemented. Useful to place the log device temporarily
1357         #     on the same physical volume as one of the mirror images. This
1358         #     policy is not recommended for mirror devices since it would break
1359         #     the redundant nature of the mirror. This policy acts like
1360         #     'remove' if no suitable device and space can be allocated for the
1361         #     replacement.
1362         # 
1363         mirror_image_fault_policy = "remove"
1364
1365         # Configuration option activation/mirror_log_fault_policy.
1366         # Defines how a device failure in a 'mirror' log LV is handled.
1367         # The mirror_image_fault_policy description for mirrored LVs also
1368         # applies to mirrored log LVs.
1369         mirror_log_fault_policy = "allocate"
1370
1371         # Configuration option activation/snapshot_autoextend_threshold.
1372         # Auto-extend a snapshot when its usage exceeds this percent.
1373         # Setting this to 100 disables automatic extension.
1374         # The minimum value is 50 (a smaller value is treated as 50.)
1375         # Also see snapshot_autoextend_percent.
1376         # Automatic extension requires dmeventd to be monitoring the LV.
1377         # 
1378         # Example
1379         # Using 70% autoextend threshold and 20% autoextend size, when a 1G
1380         # snapshot exceeds 700M, it is extended to 1.2G, and when it exceeds
1381         # 840M, it is extended to 1.44G:
1382         # snapshot_autoextend_threshold = 70
1383         # 
1384         snapshot_autoextend_threshold = 100
1385
1386         # Configuration option activation/snapshot_autoextend_percent.
1387         # Auto-extending a snapshot adds this percent extra space.
1388         # The amount of additional space added to a snapshot is this
1389         # percent of its current size.
1390         # 
1391         # Example
1392         # Using 70% autoextend threshold and 20% autoextend size, when a 1G
1393         # snapshot exceeds 700M, it is extended to 1.2G, and when it exceeds
1394         # 840M, it is extended to 1.44G:
1395         # snapshot_autoextend_percent = 20
1396         # 
1397         snapshot_autoextend_percent = 20
1398
1399         # Configuration option activation/thin_pool_autoextend_threshold.
1400         # Auto-extend a thin pool when its usage exceeds this percent.
1401         # Setting this to 100 disables automatic extension.
1402         # The minimum value is 50 (a smaller value is treated as 50.)
1403         # Also see thin_pool_autoextend_percent.
1404         # Automatic extension requires dmeventd to be monitoring the LV.
1405         # 
1406         # Example
1407         # Using 70% autoextend threshold and 20% autoextend size, when a 1G
1408         # thin pool exceeds 700M, it is extended to 1.2G, and when it exceeds
1409         # 840M, it is extended to 1.44G:
1410         # thin_pool_autoextend_threshold = 70
1411         # 
1412         thin_pool_autoextend_threshold = 100
1413
1414         # Configuration option activation/thin_pool_autoextend_percent.
1415         # Auto-extending a thin pool adds this percent extra space.
1416         # The amount of additional space added to a thin pool is this
1417         # percent of its current size.
1418         # 
1419         # Example
1420         # Using 70% autoextend threshold and 20% autoextend size, when a 1G
1421         # thin pool exceeds 700M, it is extended to 1.2G, and when it exceeds
1422         # 840M, it is extended to 1.44G:
1423         # thin_pool_autoextend_percent = 20
1424         # 
1425         thin_pool_autoextend_percent = 20
1426
1427         # Configuration option activation/mlock_filter.
1428         # Do not mlock these memory areas.
1429         # While activating devices, I/O to devices being (re)configured is
1430         # suspended. As a precaution against deadlocks, LVM pins memory it is
1431         # using so it is not paged out, and will not require I/O to reread.
1432         # Groups of pages that are known not to be accessed during activation
1433         # do not need to be pinned into memory. Each string listed in this
1434         # setting is compared against each line in /proc/self/maps, and the
1435         # pages corresponding to lines that match are not pinned. On some
1436         # systems, locale-archive was found to make up over 80% of the memory
1437         # used by the process.
1438         # 
1439         # Example
1440         # mlock_filter = [ "locale/locale-archive", "gconv/gconv-modules.cache" ]
1441         # 
1442         # This configuration option is advanced.
1443         # This configuration option does not have a default value defined.
1444
1445         # Configuration option activation/use_mlockall.
1446         # Use the old behavior of mlockall to pin all memory.
1447         # Prior to version 2.02.62, LVM used mlockall() to pin the whole
1448         # process's memory while activating devices.
1449         use_mlockall = 0
1450
1451         # Configuration option activation/monitoring.
1452         # Monitor LVs that are activated.
1453         # The --ignoremonitoring option overrides this setting.
1454         # When enabled, LVM will ask dmeventd to monitor activated LVs.
1455         monitoring = 1
1456
1457         # Configuration option activation/polling_interval.
1458         # Check pvmove or lvconvert progress at this interval (seconds).
1459         # When pvmove or lvconvert must wait for the kernel to finish
1460         # synchronising or merging data, they check and report progress at
1461         # intervals of this number of seconds. If this is set to 0 and there
1462         # is only one thing to wait for, there are no progress reports, but
1463         # the process is awoken immediately once the operation is complete.
1464         polling_interval = 15
1465
1466         # Configuration option activation/auto_set_activation_skip.
1467         # Set the activation skip flag on new thin snapshot LVs.
1468         # The --setactivationskip option overrides this setting.
1469         # An LV can have a persistent 'activation skip' flag. The flag causes
1470         # the LV to be skipped during normal activation. The lvchange/vgchange
1471         # -K option is required to activate LVs that have the activation skip
1472         # flag set. When this setting is enabled, the activation skip flag is
1473         # set on new thin snapshot LVs.
1474         # This configuration option has an automatic default value.
1475         # auto_set_activation_skip = 1
1476
1477         # Configuration option activation/activation_mode.
1478         # How LVs with missing devices are activated.
1479         # The --activationmode option overrides this setting.
1480         # 
1481         # Accepted values:
1482         #   complete
1483         #     Only allow activation of an LV if all of the Physical Volumes it
1484         #     uses are present. Other PVs in the Volume Group may be missing.
1485         #   degraded
1486         #     Like complete, but additionally RAID LVs of segment type raid1,
1487         #     raid4, raid5, radid6 and raid10 will be activated if there is no
1488         #     data loss, i.e. they have sufficient redundancy to present the
1489         #     entire addressable range of the Logical Volume.
1490         #   partial
1491         #     Allows the activation of any LV even if a missing or failed PV
1492         #     could cause data loss with a portion of the LV inaccessible.
1493         #     This setting should not normally be used, but may sometimes
1494         #     assist with data recovery.
1495         # 
1496         activation_mode = "degraded"
1497
1498         # Configuration option activation/lock_start_list.
1499         # Locking is started only for VGs selected by this list.
1500         # The rules are the same as those for volume_list.
1501         # This configuration option does not have a default value defined.
1502
1503         # Configuration option activation/auto_lock_start_list.
1504         # Locking is auto-started only for VGs selected by this list.
1505         # The rules are the same as those for auto_activation_volume_list.
1506         # This configuration option does not have a default value defined.
1507 }
1508
1509 # Configuration section metadata.
1510 # This configuration section has an automatic default value.
1511 # metadata {
1512
1513         # Configuration option metadata/check_pv_device_sizes.
1514         # Check device sizes are not smaller than corresponding PV sizes.
1515         # If device size is less than corresponding PV size found in metadata,
1516         # there is always a risk of data loss. If this option is set, then LVM
1517         # issues a warning message each time it finds that the device size is
1518         # less than corresponding PV size. You should not disable this unless
1519         # you are absolutely sure about what you are doing!
1520         # This configuration option is advanced.
1521         # This configuration option has an automatic default value.
1522         # check_pv_device_sizes = 1
1523
1524         # Configuration option metadata/record_lvs_history.
1525         # When enabled, LVM keeps history records about removed LVs in
1526         # metadata. The information that is recorded in metadata for
1527         # historical LVs is reduced when compared to original
1528         # information kept in metadata for live LVs. Currently, this
1529         # feature is supported for thin and thin snapshot LVs only.
1530         # This configuration option has an automatic default value.
1531         # record_lvs_history = 0
1532
1533         # Configuration option metadata/lvs_history_retention_time.
1534         # Retention time in seconds after which a record about individual
1535         # historical logical volume is automatically destroyed.
1536         # A value of 0 disables this feature.
1537         # This configuration option has an automatic default value.
1538         # lvs_history_retention_time = 0
1539
1540         # Configuration option metadata/pvmetadatacopies.
1541         # Number of copies of metadata to store on each PV.
1542         # The --pvmetadatacopies option overrides this setting.
1543         # 
1544         # Accepted values:
1545         #   2
1546         #     Two copies of the VG metadata are stored on the PV, one at the
1547         #     front of the PV, and one at the end.
1548         #   1
1549         #     One copy of VG metadata is stored at the front of the PV.
1550         #   0
1551         #     No copies of VG metadata are stored on the PV. This may be
1552         #     useful for VGs containing large numbers of PVs.
1553         # 
1554         # This configuration option is advanced.
1555         # This configuration option has an automatic default value.
1556         # pvmetadatacopies = 1
1557
1558         # Configuration option metadata/vgmetadatacopies.
1559         # Number of copies of metadata to maintain for each VG.
1560         # The --vgmetadatacopies option overrides this setting.
1561         # If set to a non-zero value, LVM automatically chooses which of the
1562         # available metadata areas to use to achieve the requested number of
1563         # copies of the VG metadata. If you set a value larger than the the
1564         # total number of metadata areas available, then metadata is stored in
1565         # them all. The value 0 (unmanaged) disables this automatic management
1566         # and allows you to control which metadata areas are used at the
1567         # individual PV level using pvchange --metadataignore y|n.
1568         # This configuration option has an automatic default value.
1569         # vgmetadatacopies = 0
1570
1571         # Configuration option metadata/pvmetadatasize.
1572         # Approximate number of sectors to use for each metadata copy.
1573         # VGs with large numbers of PVs or LVs, or VGs containing complex LV
1574         # structures, may need additional space for VG metadata. The metadata
1575         # areas are treated as circular buffers, so unused space becomes filled
1576         # with an archive of the most recent previous versions of the metadata.
1577         # This configuration option has an automatic default value.
1578         # pvmetadatasize = 255
1579
1580         # Configuration option metadata/pvmetadataignore.
1581         # Ignore metadata areas on a new PV.
1582         # The --metadataignore option overrides this setting.
1583         # If metadata areas on a PV are ignored, LVM will not store metadata
1584         # in them.
1585         # This configuration option is advanced.
1586         # This configuration option has an automatic default value.
1587         # pvmetadataignore = 0
1588
1589         # Configuration option metadata/stripesize.
1590         # This configuration option is advanced.
1591         # This configuration option has an automatic default value.
1592         # stripesize = 64
1593
1594         # Configuration option metadata/dirs.
1595         # Directories holding live copies of text format metadata.
1596         # These directories must not be on logical volumes!
1597         # It's possible to use LVM with a couple of directories here,
1598         # preferably on different (non-LV) filesystems, and with no other
1599         # on-disk metadata (pvmetadatacopies = 0). Or this can be in addition
1600         # to on-disk metadata areas. The feature was originally added to
1601         # simplify testing and is not supported under low memory situations -
1602         # the machine could lock up. Never edit any files in these directories
1603         # by hand unless you are absolutely sure you know what you are doing!
1604         # Use the supplied toolset to make changes (e.g. vgcfgrestore).
1605         # 
1606         # Example
1607         # dirs = [ "/etc/lvm/metadata", "/mnt/disk2/lvm/metadata2" ]
1608         # 
1609         # This configuration option is advanced.
1610         # This configuration option does not have a default value defined.
1611 # }
1612
1613 # Configuration section report.
1614 # LVM report command output formatting.
1615 # This configuration section has an automatic default value.
1616 # report {
1617
1618         # Configuration option report/output_format.
1619         # Format of LVM command's report output.
1620         # If there is more than one report per command, then the format
1621         # is applied for all reports. You can also change output format
1622         # directly on command line using --reportformat option which
1623         # has precedence over log/output_format setting.
1624         # Accepted values:
1625         #   basic
1626         #     Original format with columns and rows. If there is more than
1627         #     one report per command, each report is prefixed with report's
1628         #     name for identification.
1629         #   json
1630         #     JSON format.
1631         # This configuration option has an automatic default value.
1632         # output_format = "basic"
1633
1634         # Configuration option report/compact_output.
1635         # Do not print empty values for all report fields.
1636         # If enabled, all fields that don't have a value set for any of the
1637         # rows reported are skipped and not printed. Compact output is
1638         # applicable only if report/buffered is enabled. If you need to
1639         # compact only specified fields, use compact_output=0 and define
1640         # report/compact_output_cols configuration setting instead.
1641         # This configuration option has an automatic default value.
1642         # compact_output = 0
1643
1644         # Configuration option report/compact_output_cols.
1645         # Do not print empty values for specified report fields.
1646         # If defined, specified fields that don't have a value set for any
1647         # of the rows reported are skipped and not printed. Compact output
1648         # is applicable only if report/buffered is enabled. If you need to
1649         # compact all fields, use compact_output=1 instead in which case
1650         # the compact_output_cols setting is then ignored.
1651         # This configuration option has an automatic default value.
1652         # compact_output_cols = ""
1653
1654         # Configuration option report/aligned.
1655         # Align columns in report output.
1656         # This configuration option has an automatic default value.
1657         # aligned = 1
1658
1659         # Configuration option report/buffered.
1660         # Buffer report output.
1661         # When buffered reporting is used, the report's content is appended
1662         # incrementally to include each object being reported until the report
1663         # is flushed to output which normally happens at the end of command
1664         # execution. Otherwise, if buffering is not used, each object is
1665         # reported as soon as its processing is finished.
1666         # This configuration option has an automatic default value.
1667         # buffered = 1
1668
1669         # Configuration option report/headings.
1670         # Show headings for columns on report.
1671         # This configuration option has an automatic default value.
1672         # headings = 1
1673
1674         # Configuration option report/separator.
1675         # A separator to use on report after each field.
1676         # This configuration option has an automatic default value.
1677         # separator = " "
1678
1679         # Configuration option report/list_item_separator.
1680         # A separator to use for list items when reported.
1681         # This configuration option has an automatic default value.
1682         # list_item_separator = ","
1683
1684         # Configuration option report/prefixes.
1685         # Use a field name prefix for each field reported.
1686         # This configuration option has an automatic default value.
1687         # prefixes = 0
1688
1689         # Configuration option report/quoted.
1690         # Quote field values when using field name prefixes.
1691         # This configuration option has an automatic default value.
1692         # quoted = 1
1693
1694         # Configuration option report/columns_as_rows.
1695         # Output each column as a row.
1696         # If set, this also implies report/prefixes=1.
1697         # This configuration option has an automatic default value.
1698         # columns_as_rows = 0
1699
1700         # Configuration option report/binary_values_as_numeric.
1701         # Use binary values 0 or 1 instead of descriptive literal values.
1702         # For columns that have exactly two valid values to report
1703         # (not counting the 'unknown' value which denotes that the
1704         # value could not be determined).
1705         # This configuration option has an automatic default value.
1706         # binary_values_as_numeric = 0
1707
1708         # Configuration option report/time_format.
1709         # Set time format for fields reporting time values.
1710         # Format specification is a string which may contain special character
1711         # sequences and ordinary character sequences. Ordinary character
1712         # sequences are copied verbatim. Each special character sequence is
1713         # introduced by the '%' character and such sequence is then
1714         # substituted with a value as described below.
1715         # 
1716         # Accepted values:
1717         #   %a
1718         #     The abbreviated name of the day of the week according to the
1719         #     current locale.
1720         #   %A
1721         #     The full name of the day of the week according to the current
1722         #     locale.
1723         #   %b
1724         #     The abbreviated month name according to the current locale.
1725         #   %B
1726         #     The full month name according to the current locale.
1727         #   %c
1728         #     The preferred date and time representation for the current
1729         #     locale (alt E)
1730         #   %C
1731         #     The century number (year/100) as a 2-digit integer. (alt E)
1732         #   %d
1733         #     The day of the month as a decimal number (range 01 to 31).
1734         #     (alt O)
1735         #   %D
1736         #     Equivalent to %m/%d/%y. (For Americans only. Americans should
1737         #     note that in other countries%d/%m/%y is rather common. This
1738         #     means that in international context this format is ambiguous and
1739         #     should not be used.
1740         #   %e
1741         #     Like %d, the day of the month as a decimal number, but a leading
1742         #     zero is replaced by a space. (alt O)
1743         #   %E
1744         #     Modifier: use alternative local-dependent representation if
1745         #     available.
1746         #   %F
1747         #     Equivalent to %Y-%m-%d (the ISO 8601 date format).
1748         #   %G
1749         #     The ISO 8601 week-based year with century as adecimal number.
1750         #     The 4-digit year corresponding to the ISO week number (see %V).
1751         #     This has the same format and value as %Y, except that if the
1752         #     ISO week number belongs to the previous or next year, that year
1753         #     is used instead.
1754         #   %g
1755         #     Like %G, but without century, that is, with a 2-digit year
1756         #     (00-99).
1757         #   %h
1758         #     Equivalent to %b.
1759         #   %H
1760         #     The hour as a decimal number using a 24-hour clock
1761         #     (range 00 to 23). (alt O)
1762         #   %I
1763         #     The hour as a decimal number using a 12-hour clock
1764         #     (range 01 to 12). (alt O)
1765         #   %j
1766         #     The day of the year as a decimal number (range 001 to 366).
1767         #   %k
1768         #     The hour (24-hour clock) as a decimal number (range 0 to 23);
1769         #     single digits are preceded by a blank. (See also %H.)
1770         #   %l
1771         #     The hour (12-hour clock) as a decimal number (range 1 to 12);
1772         #     single digits are preceded by a blank. (See also %I.)
1773         #   %m
1774         #     The month as a decimal number (range 01 to 12). (alt O)
1775         #   %M
1776         #     The minute as a decimal number (range 00 to 59). (alt O)
1777         #   %O
1778         #     Modifier: use alternative numeric symbols.
1779         #   %p
1780         #     Either "AM" or "PM" according to the given time value,
1781         #     or the corresponding strings for the current locale. Noon is
1782         #     treated as "PM" and midnight as "AM".
1783         #   %P
1784         #     Like %p but in lowercase: "am" or "pm" or a corresponding
1785         #     string for the current locale.
1786         #   %r
1787         #     The time in a.m. or p.m. notation. In the POSIX locale this is
1788         #     equivalent to %I:%M:%S %p.
1789         #   %R
1790         #     The time in 24-hour notation (%H:%M). For a version including
1791         #     the seconds, see %T below.
1792         #   %s
1793         #     The number of seconds since the Epoch,
1794         #     1970-01-01 00:00:00 +0000 (UTC)
1795         #   %S
1796         #     The second as a decimal number (range 00 to 60). (The range is
1797         #     up to 60 to allow for occasional leap seconds.) (alt O)
1798         #   %t
1799         #     A tab character.
1800         #   %T
1801         #     The time in 24-hour notation (%H:%M:%S).
1802         #   %u
1803         #     The day of the week as a decimal, range 1 to 7, Monday being 1.
1804         #     See also %w. (alt O)
1805         #   %U
1806         #     The week number of the current year as a decimal number,
1807         #     range 00 to 53, starting with the first Sunday as the first
1808         #     day of week 01. See also %V and %W. (alt O)
1809         #   %V
1810         #     The ISO 8601 week number of the current year as a decimal number,
1811         #     range 01 to 53, where week 1 is the first week that has at least
1812         #     4 days in the new year. See also %U and %W. (alt O)
1813         #   %w
1814         #     The day of the week as a decimal, range 0 to 6, Sunday being 0.
1815         #     See also %u. (alt O)
1816         #   %W
1817         #     The week number of the current year as a decimal number,
1818         #     range 00 to 53, starting with the first Monday as the first day
1819         #     of week 01. (alt O)
1820         #   %x
1821         #     The preferred date representation for the current locale without
1822         #     the time. (alt E)
1823         #   %X
1824         #     The preferred time representation for the current locale without
1825         #     the date. (alt E)
1826         #   %y
1827         #     The year as a decimal number without a century (range 00 to 99).
1828         #     (alt E, alt O)
1829         #   %Y
1830         #     The year as a decimal number including the century. (alt E)
1831         #   %z
1832         #     The +hhmm or -hhmm numeric timezone (that is, the hour and minute
1833         #     offset from UTC).
1834         #   %Z
1835         #     The timezone name or abbreviation.
1836         #   %%
1837         #     A literal '%' character.
1838         # 
1839         # This configuration option has an automatic default value.
1840         # time_format = "%Y-%m-%d %T %z"
1841
1842         # Configuration option report/devtypes_sort.
1843         # List of columns to sort by when reporting 'lvm devtypes' command.
1844         # See 'lvm devtypes -o help' for the list of possible fields.
1845         # This configuration option has an automatic default value.
1846         # devtypes_sort = "devtype_name"
1847
1848         # Configuration option report/devtypes_cols.
1849         # List of columns to report for 'lvm devtypes' command.
1850         # See 'lvm devtypes -o help' for the list of possible fields.
1851         # This configuration option has an automatic default value.
1852         # devtypes_cols = "devtype_name,devtype_max_partitions,devtype_description"
1853
1854         # Configuration option report/devtypes_cols_verbose.
1855         # List of columns to report for 'lvm devtypes' command in verbose mode.
1856         # See 'lvm devtypes -o help' for the list of possible fields.
1857         # This configuration option has an automatic default value.
1858         # devtypes_cols_verbose = "devtype_name,devtype_max_partitions,devtype_description"
1859
1860         # Configuration option report/lvs_sort.
1861         # List of columns to sort by when reporting 'lvs' command.
1862         # See 'lvs -o help' for the list of possible fields.
1863         # This configuration option has an automatic default value.
1864         # lvs_sort = "vg_name,lv_name"
1865
1866         # Configuration option report/lvs_cols.
1867         # List of columns to report for 'lvs' command.
1868         # See 'lvs -o help' for the list of possible fields.
1869         # This configuration option has an automatic default value.
1870         # lvs_cols = "lv_name,vg_name,lv_attr,lv_size,pool_lv,origin,data_percent,metadata_percent,move_pv,mirror_log,copy_percent,convert_lv"
1871
1872         # Configuration option report/lvs_cols_verbose.
1873         # List of columns to report for 'lvs' command in verbose mode.
1874         # See 'lvs -o help' for the list of possible fields.
1875         # This configuration option has an automatic default value.
1876         # lvs_cols_verbose = "lv_name,vg_name,seg_count,lv_attr,lv_size,lv_major,lv_minor,lv_kernel_major,lv_kernel_minor,pool_lv,origin,data_percent,metadata_percent,move_pv,copy_percent,mirror_log,convert_lv,lv_uuid,lv_profile"
1877
1878         # Configuration option report/vgs_sort.
1879         # List of columns to sort by when reporting 'vgs' command.
1880         # See 'vgs -o help' for the list of possible fields.
1881         # This configuration option has an automatic default value.
1882         # vgs_sort = "vg_name"
1883
1884         # Configuration option report/vgs_cols.
1885         # List of columns to report for 'vgs' command.
1886         # See 'vgs -o help' for the list of possible fields.
1887         # This configuration option has an automatic default value.
1888         # vgs_cols = "vg_name,pv_count,lv_count,snap_count,vg_attr,vg_size,vg_free"
1889
1890         # Configuration option report/vgs_cols_verbose.
1891         # List of columns to report for 'vgs' command in verbose mode.
1892         # See 'vgs -o help' for the list of possible fields.
1893         # This configuration option has an automatic default value.
1894         # vgs_cols_verbose = "vg_name,vg_attr,vg_extent_size,pv_count,lv_count,snap_count,vg_size,vg_free,vg_uuid,vg_profile"
1895
1896         # Configuration option report/pvs_sort.
1897         # List of columns to sort by when reporting 'pvs' command.
1898         # See 'pvs -o help' for the list of possible fields.
1899         # This configuration option has an automatic default value.
1900         # pvs_sort = "pv_name"
1901
1902         # Configuration option report/pvs_cols.
1903         # List of columns to report for 'pvs' command.
1904         # See 'pvs -o help' for the list of possible fields.
1905         # This configuration option has an automatic default value.
1906         # pvs_cols = "pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free"
1907
1908         # Configuration option report/pvs_cols_verbose.
1909         # List of columns to report for 'pvs' command in verbose mode.
1910         # See 'pvs -o help' for the list of possible fields.
1911         # This configuration option has an automatic default value.
1912         # pvs_cols_verbose = "pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,dev_size,pv_uuid"
1913
1914         # Configuration option report/segs_sort.
1915         # List of columns to sort by when reporting 'lvs --segments' command.
1916         # See 'lvs --segments -o help' for the list of possible fields.
1917         # This configuration option has an automatic default value.
1918         # segs_sort = "vg_name,lv_name,seg_start"
1919
1920         # Configuration option report/segs_cols.
1921         # List of columns to report for 'lvs --segments' command.
1922         # See 'lvs --segments -o help' for the list of possible fields.
1923         # This configuration option has an automatic default value.
1924         # segs_cols = "lv_name,vg_name,lv_attr,stripes,segtype,seg_size"
1925
1926         # Configuration option report/segs_cols_verbose.
1927         # List of columns to report for 'lvs --segments' command in verbose mode.
1928         # See 'lvs --segments -o help' for the list of possible fields.
1929         # This configuration option has an automatic default value.
1930         # segs_cols_verbose = "lv_name,vg_name,lv_attr,seg_start,seg_size,stripes,segtype,stripesize,chunksize"
1931
1932         # Configuration option report/pvsegs_sort.
1933         # List of columns to sort by when reporting 'pvs --segments' command.
1934         # See 'pvs --segments -o help' for the list of possible fields.
1935         # This configuration option has an automatic default value.
1936         # pvsegs_sort = "pv_name,pvseg_start"
1937
1938         # Configuration option report/pvsegs_cols.
1939         # List of columns to sort by when reporting 'pvs --segments' command.
1940         # See 'pvs --segments -o help' for the list of possible fields.
1941         # This configuration option has an automatic default value.
1942         # pvsegs_cols = "pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,pvseg_start,pvseg_size"
1943
1944         # Configuration option report/pvsegs_cols_verbose.
1945         # List of columns to sort by when reporting 'pvs --segments' command in verbose mode.
1946         # See 'pvs --segments -o help' for the list of possible fields.
1947         # This configuration option has an automatic default value.
1948         # pvsegs_cols_verbose = "pv_name,vg_name,pv_fmt,pv_attr,pv_size,pv_free,pvseg_start,pvseg_size,lv_name,seg_start_pe,segtype,seg_pe_ranges"
1949
1950         # Configuration option report/vgs_cols_full.
1951         # List of columns to report for lvm fullreport's 'vgs' subreport.
1952         # See 'vgs -o help' for the list of possible fields.
1953         # This configuration option has an automatic default value.
1954         # vgs_cols_full = "vg_all"
1955
1956         # Configuration option report/pvs_cols_full.
1957         # List of columns to report for lvm fullreport's 'vgs' subreport.
1958         # See 'pvs -o help' for the list of possible fields.
1959         # This configuration option has an automatic default value.
1960         # pvs_cols_full = "pv_all"
1961
1962         # Configuration option report/lvs_cols_full.
1963         # List of columns to report for lvm fullreport's 'lvs' subreport.
1964         # See 'lvs -o help' for the list of possible fields.
1965         # This configuration option has an automatic default value.
1966         # lvs_cols_full = "lv_all"
1967
1968         # Configuration option report/pvsegs_cols_full.
1969         # List of columns to report for lvm fullreport's 'pvseg' subreport.
1970         # See 'pvs --segments -o help' for the list of possible fields.
1971         # This configuration option has an automatic default value.
1972         # pvsegs_cols_full = "pvseg_all,pv_uuid,lv_uuid"
1973
1974         # Configuration option report/segs_cols_full.
1975         # List of columns to report for lvm fullreport's 'seg' subreport.
1976         # See 'lvs --segments -o help' for the list of possible fields.
1977         # This configuration option has an automatic default value.
1978         # segs_cols_full = "seg_all,lv_uuid"
1979
1980         # Configuration option report/vgs_sort_full.
1981         # List of columns to sort by when reporting lvm fullreport's 'vgs' subreport.
1982         # See 'vgs -o help' for the list of possible fields.
1983         # This configuration option has an automatic default value.
1984         # vgs_sort_full = "vg_name"
1985
1986         # Configuration option report/pvs_sort_full.
1987         # List of columns to sort by when reporting lvm fullreport's 'vgs' subreport.
1988         # See 'pvs -o help' for the list of possible fields.
1989         # This configuration option has an automatic default value.
1990         # pvs_sort_full = "pv_name"
1991
1992         # Configuration option report/lvs_sort_full.
1993         # List of columns to sort by when reporting lvm fullreport's 'lvs' subreport.
1994         # See 'lvs -o help' for the list of possible fields.
1995         # This configuration option has an automatic default value.
1996         # lvs_sort_full = "vg_name,lv_name"
1997
1998         # Configuration option report/pvsegs_sort_full.
1999         # List of columns to sort by when reporting for lvm fullreport's 'pvseg' subreport.
2000         # See 'pvs --segments -o help' for the list of possible fields.
2001         # This configuration option has an automatic default value.
2002         # pvsegs_sort_full = "pv_uuid,pvseg_start"
2003
2004         # Configuration option report/segs_sort_full.
2005         # List of columns to sort by when reporting lvm fullreport's 'seg' subreport.
2006         # See 'lvs --segments -o help' for the list of possible fields.
2007         # This configuration option has an automatic default value.
2008         # segs_sort_full = "lv_uuid,seg_start"
2009
2010         # Configuration option report/mark_hidden_devices.
2011         # Use brackets [] to mark hidden devices.
2012         # This configuration option has an automatic default value.
2013         # mark_hidden_devices = 1
2014
2015         # Configuration option report/two_word_unknown_device.
2016         # Use the two words 'unknown device' in place of '[unknown]'.
2017         # This is displayed when the device for a PV is not known.
2018         # This configuration option has an automatic default value.
2019         # two_word_unknown_device = 0
2020 # }
2021
2022 # Configuration section dmeventd.
2023 # Settings for the LVM event daemon.
2024 dmeventd {
2025
2026         # Configuration option dmeventd/mirror_library.
2027         # The library dmeventd uses when monitoring a mirror device.
2028         # libdevmapper-event-lvm2mirror.so attempts to recover from
2029         # failures. It removes failed devices from a volume group and
2030         # reconfigures a mirror as necessary. If no mirror library is
2031         # provided, mirrors are not monitored through dmeventd.
2032         mirror_library = "libdevmapper-event-lvm2mirror.so"
2033
2034         # Configuration option dmeventd/raid_library.
2035         # This configuration option has an automatic default value.
2036         # raid_library = "libdevmapper-event-lvm2raid.so"
2037
2038         # Configuration option dmeventd/snapshot_library.
2039         # The library dmeventd uses when monitoring a snapshot device.
2040         # libdevmapper-event-lvm2snapshot.so monitors the filling of snapshots
2041         # and emits a warning through syslog when the usage exceeds 80%. The
2042         # warning is repeated when 85%, 90% and 95% of the snapshot is filled.
2043         snapshot_library = "libdevmapper-event-lvm2snapshot.so"
2044
2045         # Configuration option dmeventd/thin_library.
2046         # The library dmeventd uses when monitoring a thin device.
2047         # libdevmapper-event-lvm2thin.so monitors the filling of a pool
2048         # and emits a warning through syslog when the usage exceeds 80%. The
2049         # warning is repeated when 85%, 90% and 95% of the pool is filled.
2050         thin_library = "libdevmapper-event-lvm2thin.so"
2051
2052         # Configuration option dmeventd/executable.
2053         # The full path to the dmeventd binary.
2054         # This configuration option has an automatic default value.
2055         # executable = "/sbin/dmeventd"
2056 }
2057
2058 # Configuration section tags.
2059 # Host tag settings.
2060 # This configuration section has an automatic default value.
2061 # tags {
2062
2063         # Configuration option tags/hosttags.
2064         # Create a host tag using the machine name.
2065         # The machine name is nodename returned by uname(2).
2066         # This configuration option has an automatic default value.
2067         # hosttags = 0
2068
2069         # Configuration section tags/<tag>.
2070         # Replace this subsection name with a custom tag name.
2071         # Multiple subsections like this can be created. The '@' prefix for
2072         # tags is optional. This subsection can contain host_list, which is a
2073         # list of machine names. If the name of the local machine is found in
2074         # host_list, then the name of this subsection is used as a tag and is
2075         # applied to the local machine as a 'host tag'. If this subsection is
2076         # empty (has no host_list), then the subsection name is always applied
2077         # as a 'host tag'.
2078         # 
2079         # Example
2080         # The host tag foo is given to all hosts, and the host tag
2081         # bar is given to the hosts named machine1 and machine2.
2082         # tags { foo { } bar { host_list = [ "machine1", "machine2" ] } }
2083         # 
2084         # This configuration section has variable name.
2085         # This configuration section has an automatic default value.
2086         # tag {
2087
2088                 # Configuration option tags/<tag>/host_list.
2089                 # A list of machine names.
2090                 # These machine names are compared to the nodename returned
2091                 # by uname(2). If the local machine name matches an entry in
2092                 # this list, the name of the subsection is applied to the
2093                 # machine as a 'host tag'.
2094                 # This configuration option does not have a default value defined.
2095         # }
2096 # }